AirCube Com2 – TH Touch

Portable Sampler

Description

The AirCube Com2-TH Touch constant-flow sampler is part of the new generation of the successful AirCube portable sampler line made by AMS Analitica. Compact and lightweight, it features an exclusive proportional valve for precise regulation of the intake flow with pressure control.

The sampler can be adjusted with an operating flow rate between 0.4 and 30 L/min, without the need for bypass valves or special regulators for operating in low-flow ranges. The high-resolution touchscreen display allows for easy and intuitive data setup. During operation, the display shows all sampling data in real time, such as instantaneous flow and average flow over the period, instantaneous temperature at the meter and the average over the period, instantaneous atmospheric pressure and the average over the period, partial sampled volume, and sampling time. The display also shows a graph representing sampling progress, broken down by suction flow and time, as well as environmental parameters.

This option allows you to verify sampling effectiveness and validate data by calculating standard deviation. The AirCube Com2-TH Touch sampler is equipped with an interface for sequential sampling devices for PTS dust and airborne fibers and is ready for connection to IsoCube isokinetic parameter measurement instruments, effectively making the AirCube Com2-TH Touch an automatic isokinetic sampler.

Main sampler features

  • High pressure drop compensation
  • Suction flow rate 0.4-30 L/min without manual adjustment
  • Flow control via volumetric counter with electronic reader
  • Sampling data available on the display in real time
  • Automatic compensation related to temperature, flow, and environmental conditions
  • 4.3” color touchscreen display
  • Data download via USB port
  • Wi-Fi interface for remote control (Optional)
  • Bluetooth interface for IsoCube control for isokinetic measurements (Optional)
  • Motorized valve with differential pressure control for regulation and stabilization in low-flow sampling
  • Suction flow compensation based on external temperature and pressure
  • Single-head diaphragm suction pump and pulsation reducer with built-in pressure control
  • Sampling settings for times, volumes, and flows directly from the touchscreen display
  • 32 GB internal memory (64 GB optional)
  • Weight: 8 kg (Not Power Pack Cube)
  • Possibility of sequential group management External for dust and airborne fibres
  • Power supply 220V/50 Hz, 150 Watt / 12 Vdc with Power Pack Cube (Optional)
  • Dimensions: 28x28x28 cm (LxWxH – Weight 8 Kg)

Other Features

Stack Emissions Monitoring

The AirCube Com2-TH Touch is the professional choice for emissions sampling control. It can be combined with the new Iso Cube for automatic isokinetic sampling applications compliant with EN-13284:2017, EN-ISO 16911, and EPA M5 and M17 requirements.

The AirCube sampler, combined with the isokinetic data acquisition system IsoCube, can seamlessly perform any emission sampling protocol with “filter in-stack” or “filter out-stack” filters. Additional applications for dioxins, metals, inorganic acids, mercury, sulfur dioxide, and ammonia are available with the use of heated probes and specific bubbling kits.

Asbestos Fiber Sampling

Processes that in any way come into contact with asbestos automatically require personnel or environmental monitoring to subsequently quantify airborne fibers. Remediation, construction sites, and tunnel excavations are all applications where the AirCube Com2-TH sampler supports companies involved in these types of activities. For environmental sampling, membranes or pre-filled cassettes with a diameter of 25 mm can be used. Alternatively, in the case of high dust concentrations due to various processes, a larger filter diameter such as 47 mm can also be used. The support will be positioned on a stand in a suitable predetermined location and connected to a constant flow sampler with a flow rate between 6 and 10 L/min (max 16 L/min according to US-EPA protocol). Sampling time will depend on the duration of the operations and in any case not less than 3000 liters of total sample.

Bioaerosol Sampling

The BioSampler® (SKC Inc.) is designed for sampling microorganisms and biologically inert particles at a flow rate of 12.5 L/min. The device consists of three parts: the inlet section, the nozzle section, and the collection vessel section. The presence of three nozzles in the collection vessel, allowing a known and identical volume of air to pass through each nozzle, allows the airflow to entrain the liquid and cause it to rotate upward in the region where the air flows from the nozzles, reaching the inner surface of the vessel. The centrifugal motion of the airflow eliminates the impact effect of the microorganisms, eliminating stress during the sampling period. The BioSampler® can be used with water or liquids of similar viscosities and with non-evaporating fluids with a viscosity up to three times that of water.

Sampling of Respirable Particulate Matter in Indoor Environments

The sampling methods (Unichim 2010) dedicated to the respirable fraction, among other procedures, also include fixed-site area sampling. The sampler must be mounted on a stand, approximately at eye level (150-160 cm from the floor), away from obstacles, air vents, or strong drafts. However, be careful not to compare data from area pre-selectors with personal samples, as fixed-site samplers may provide lower concentration data. The AirCube samplers from AMS Analitica are well suited to this type of application, ensuring excellent performance in terms of flow consistency and pressure drop compensation. The new OSHA standard for silica dust requires larger air samples to achieve better sensitivity for laboratory analysis, and the application of the FSP-10 high-flow cyclone is described in the NIOSH ECM/2011/03 report, along with the use of a 37 mm, 5-micron PVC filter membrane. Developed in Europe, the FSP-10 cyclone ensures particle removal (50% at 4 microns) using an intake flow rate of 11.2 L/min.

TSP Sequential Sampling Module

It is based on a support with two 8-filter arrays, each programmable directly from the sampler. The user can select the sampling time or volume depending on the application needs. The units can accommodate 47 mm and 25 mm supports and are suitable for sampling TSP dust or airborne fibers.

Portable PM10 and PM2.5 sampling kit with US EPA-style impactor

The US EPA-style PM10 and PM2.5 particulate sampling pre-selector is part of a new portable field sampling system combined with an AirCube COM2-TH constant-flow sampler. The PM pre-selectors are manufactured in full compliance with US EPA requirements based on the US EPA Reference Method Cfr. 40. They are made entirely of anodized aluminum for outdoor applications and are available with an optional ambient temperature sensor.

Flow regulation range: 0.4 – 30 L/min without adapters or bypass

Maximum flow rate: 29 L/min with 47 mm GF1 filter

Pressure loss compensation: Electronic control across the entire flow range

Suction pump: Single diaphragm head with pulsation dampener

Flow regulation: Displayed via pressure control and automatic adjustment

Flow control: Volumetric flow meter with digital electronic detector

Flow measurement accuracy: 2% with certified primary flow control

Sampling parameter setting: Directly via the 4.3″ color touchscreen display

Sampling parameter display: 4.3″ color touchscreen display

Temperature sensor accuracy at meter: +/- 0.1°C

Barometric pressure sensor accuracy: +/- 0.1

Remote control: WiFi (optional) or GSM modems (optional)

Speed ​​control and wind direction: Externally mounted sensors (optional)

Available connections: Bluetooth for IsoCube for isokinetic sampling

Available data outputs: USB

Available interfaces: Standard sequential module for up to 16 filters

Power supply: 220V AC with optional battery pack

Weight: 8 kg

The electronic pc board complies with the requirements of the RoHS-2025 regulation. CE compliant with EN 61010-1:2010 + A1:2019 + AC:2019, EN 61326-1:2013, EN IEC 63000:2018. Compliant with ISO 13137:2023.

The sampler is supplied with a user manual, calibration certificate, test report, power cable, and a USB flash drive for data download.

Request information

Senza Titolo(Required)